LCD module data
Numeric
Character
Mixed
- ≡ Uniden FP203 ✘
- ≡ Uniden FP204 ✘
- ≡ VIP89Z G-Code ✘
Graphic
key: ≡ parallel, ↔ serial, ~ LVDS, _ unknown, ✘ discarded as not useful
Resources
This is an old revision of the document!
| LCD Description | |
|---|---|
| Model | NG-87243-001 |
| Manufacturer | Samsung? |
| Recovered from | Nec DTR-16D-1A |
| Board IDs | NG-87243-001, |
| Alt. board IDs | A50-002005-003, MBCF24302Z04. A50-002005-002, MBC24302Z02 1) |
| LCD type | positive |
| Polarizer type | reflective |
| Columns | 24 |
| Rows | 3 |
| Char matrix | 5×7 |
| Driver IC | Hitachi HD44780 compatible (covered in epoxy) |
| Backlight | - |
| Arduino driver | LiquidCrystal_24x3.h2) |
| Connector | PCB flex |
| Num Pins | 16 |
| Pin spacing | 0.05“ |
| Module size | 98 x 37 mm |
| Measured | Connector pin-out | Arduino test rig | ||||||
|---|---|---|---|---|---|---|---|---|
| Pin# | Main board | LCD board | LCD on | LCD off | IC pin | Label | Pin | colour |
| 1 | Green LED K | 1.7V | 0.0V | |||||
| 2 | LED A common | 0.8V | 0.0V | |||||
| 3 | Red LED K | 1.9V | 0.0V | |||||
| 4 | 2.9V | 0.1V | RS | |||||
| 5 | 0.4V | 0.1V | E | |||||
| 6 | 164k | 0.7V | 0.1V | D0 | ||||
| 7 | 1.4M | 0.6V | 0.2V | D1 | ||||
| 8 | 0.6V | 3.3V | D2 | |||||
| 9 | 0.3V | 3.3V | D3 | |||||
| 10 | 3.45k | 120k | 3.3V | 3.3V | Vcc | |||
| 11 | GND | GND | 0.0V | 0.0V | GND | |||
| 12 | 100k | 1.9V | 1.7V | Contrast | ||||
| 13 | NC | 120k | 3.3V | 3.3V | ||||
| 14 | NC | 0.0V | 0.0V | |||||
| 15 | GND | GND | 0.0V | 0.0V | 3) | |||
| 16 | NC | 0.0V | 0.0V | |||||
The connector pins aren't labeled on the LCD module, I have used the numbering on the phone board. This corresponds to viewing the LCD module from the back, with the flex connector at the top and numbering the pins 1 to 16 from left to right.
In the phones it seems to operate with a contrast voltage of 1.9V, but I had to supply 2.3V on my test rig, might be because supply voltage was only 3V rather than 3.3V.
The LCD modules can be swapped out from the phones quite simply, and are interchangable between the DTR-16D and DTR-8D, DTH series and possibly other models. See https://www.commgear.com/Documents/LCD%20Replacement-Instructions.pdf.
The slightly modified LCD library 4):
- liquidcrystal_24x3.h, SPI LCD library
- liquidcrystal_24x3.cpp, SPI LCD library
Datasheets
Examples :
 |
 |
 |
 |
 |
 |
 |
 |  |
 |  |
 |  |
 |  |
 |
 |
 |
 |
 |
 |
 |
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International