My Projects

You are here: start » electronic » lcd » mdp12bs17srt

My Projects

User Tools

Site Tools

You are here: start » electronic » lcd » mdp12bs17srt

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
electronic:lcd:mdp12bs17srt [2018/10/21 10:14] – tonyelectronic:lcd:mdp12bs17srt [2026/09/26 08:26] (current) – tony
Line 1: Line 1:
 {{ :electronic:lcd:p8170777a.jpg?200|MDP12BS17-SR-T}} {{ :electronic:lcd:p8170777a.jpg?200|MDP12BS17-SR-T}}
-^<html><p style="text-align:center">LCD Description</p></html>|| +^  LCD Description  || 
-^Model|**MDP12BS17-SR-T** (2142717-01) (2142716 00)|+^Model|**MDP12BS17-SR-T** |
 ^Manufacturer| | ^Manufacturer| |
 ^Recovered from|Epson WF-2530 ((http://repaircafe-zwijndrecht.nl/wp-tech/Repair/epson-WF2510_SI_1474287827.pdf))| ^Recovered from|Epson WF-2530 ((http://repaircafe-zwijndrecht.nl/wp-tech/Repair/epson-WF2510_SI_1474287827.pdf))|
 +^Board IDs|2142717-01, 2142716 00|
 ^LCD type|positive| ^LCD type|positive|
 ^Polarizer type|reflective| ^Polarizer type|reflective|
-^Columns|128 pixels ((Bitmap graphical display as characters have proportional spacing))| +^Columns|128 pixels| 
-^Rows|32 pixels| +^Rows|28 pixels| 
-^Char matrix|-| +^Char matrix|3x14 to 8x14  ((Bitmap graphical display, characters have proportional spacing))| 
-^Driver IC|mounted on LCD glass (CoG)|+^Driver IC|ST7567 (CoG) (( {{:electronic:datasheet:sitronix:st7567.pdf}}))|
 ^Backlight|-| ^Backlight|-|
 ^Arduino driver| | ^Arduino driver| |
Line 16: Line 17:
 ^Pin spacing|0.07"| ^Pin spacing|0.07"|
  
-^LCD1 Pinout^^^Arduino test rig ((reminder for my personal testing, not useful for anyone else!))|| +^  LCD1 Pinout  ^^^^  Arduino test rig ((reminder for my personal testing, not useful for anyone else!))  ||| 
-^Pin#^Label^Connected to^Pin^colour| +^Pin#^IC Label^Funtion^Connected to^Measured^Pin^colour| 
-^1| |(cn1 pin 8)| +^1|CSB|Chip Select|(cn1 pin 8)|3.38V| 
-^2|CS?|(74VHC595 pin 4 (Qe))| +^2|RSTB|Reset|(74VHC595 pin 4 (Qe))|3.38V| 
-^3|DATA IN?|(cn1 pin6, 74VHC595 pin 14 (SER data input) via 100Ω)| +^3|A0|Register select|(cn1 pin6, 74VHC595 pin 14 (SER data input) via 100Ω)|0V| | 
-^4|CLK?|(cn1 pin5 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω)| +^4|SCLK|Clock|(cn1 pin5 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω) 250kHz or 3MHz|0V| 
-^5|output?|(cn1 pin2),  (74VHC165 pin 9 (QH) via 3.3k)| +^5|SDA|Data In|(cn1 pin2),  (74VHC165 pin 9 (QH) via 3.3k)|3.38V| 
-^6|Vcc?| +^6|VDD|Power |3.38V, bypass capacitor to GND| 
-^7|GND| +^7|VSS|Ground|oV| 
-^8| |capacitor to GND|+^8|VG|LCD power|capacitor to GND|6.94V|
  
-^JK33149A, 2142717-01 Board, CN1 pinout^^^Arduino test rig ((reminder for my personal testing, not useful for anyone else!))||+^  JK33149A, 2142717-01 Board, CN1 pinout  ^^^  Arduino test rig ((reminder for my personal testing, not useful for anyone else!))  ||
 ^Pin#^Label^Connected to^Pin^colour| ^Pin#^Label^Connected to^Pin^colour|
 ^1| |Buzzer-| ^1| |Buzzer-|
-^2| |(lcd pin5)|+^2|SDA|(lcd pin5)|
 ^3|GND| ^3|GND|
-^4|Vcc?| +^4|Vcc| 
-^5|CLK?|(lcd pin4 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω)| +^5|CLK|(lcd pin4 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω)| 
-^6| |(lcd pin3 via 100Ω)|+^6|RS|(lcd pin3 via 100Ω)|
 ^7| |(74VHC595 pin 13 (output enable))| ^7| |(74VHC595 pin 13 (output enable))|
-^8| |(lcd pin1)|+^8|CS|(lcd pin1)|
 ^9| |(74VHC165 pin 1 (parallel load))| ^9| |(74VHC165 pin 1 (parallel load))|
 ^10| |SW1 (closes to gnd) (power button)| ^10| |SW1 (closes to gnd) (power button)|
Line 44: Line 45:
 "2 line bitmap LCD" Approximately 20 characters by 2 rows.\\ "2 line bitmap LCD" Approximately 20 characters by 2 rows.\\
 IC1, 74VHC165 (8bit parallel line/serial out shift register) is used for serializing the keyswitch selections,\\ IC1, 74VHC165 (8bit parallel line/serial out shift register) is used for serializing the keyswitch selections,\\
-IC2. 74VHC595 (8-Bit Shift Register with Output Latches) is used for decoding serial data to latched outputs to turn on status LEDs (Power, Wifi, ADF) and one LCD control line (chip select?)\\ +IC2. 74VHC595 (8-Bit Shift Register with Output Latches) is used for decoding serial data to latched outputs to turn on status LEDs (Power, Wifi, ADF) and one LCD control line (chip select)\\ 
-IC1 & IC2 can use power supplies of 2V to 5.5V, so LCD maybe 3.3V?+IC1 & IC2 can use power supplies of 2V to 5.5V, LCD 3.3V powered?
  
 +\\
 +===== Datasheets =====
 +  * {{:electronic:lcd:epson_wf-2530_lcd.pdf|LCD initialisation sequence from sigrok analysis}}
 +  * {{:electronic:lcd:epson_wf-2530_lcd.sr|LCD initialisation sequence in sigrok format}}
 +
 +\\
 ---- ----
-===== Examples : =====+===== Examples ===== 
 + 
 +{{:electronic:lcd:p8170777a.jpg?800|MDP12BS17-SR-T front}} 
 + 
 + 
 +{{:electronic:lcd:p1043588a.jpg?800|MDP12BS17-SR-T overview with board}} 
 + 
 +{{:electronic:lcd:pa252270a.jpg?300|MDP12BS17-SR-T connector}}
  
-{{:electronic:lcd:p8170777a.jpg?800|MDP12BS17-SR-T}}+{{:electronic:lcd:pa252266b.jpg?800|MDP12BS17-SR-T examples}}
  

Page Tools

electronic/lcd/mdp12bs17srt.1540116854.txt.gz · Last modified: 2018/10/21 10:14 by tony
CC Attribution-Share Alike 4.0 International Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International