Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| electronic:lcd:lbp8iii [2018/04/08 22:37] – tony | electronic:lcd:lbp8iii [2026/09/26 10:33] (current) – tony | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | {{ : | ||
| + | ^ LCD Description | ||
| + | ^Model|**GB-1494V-OS SH84149**| | ||
| ^Manufacturer|Canon| | ^Manufacturer|Canon| | ||
| - | ^Model|GB-1494V-OS SH84149| | + | ^Recovered from|Canon LBP-8 III printer, HP Laserjet |
| - | ^Recovered from|Canon LBP-8 III printer| | + | ^Board IDs|SG54159((LBP-8III)), |
| - | ^Columns|16| | + | ^LCD type|positive| |
| + | ^Polarizer type|reflective| | ||
| + | ^Columns|16 | ||
| ^Rows|1| | ^Rows|1| | ||
| ^Char matrix|5x7| | ^Char matrix|5x7| | ||
| ^Driver IC|Hitachi HD44780A00| | ^Driver IC|Hitachi HD44780A00| | ||
| ^Backlight|-| | ^Backlight|-| | ||
| - | ^Arduino driver|44780| | + | ^Arduino driver|LiquidCrystal.h| |
| ^Connector|pin header| | ^Connector|pin header| | ||
| ^Num Pins|14| | ^Num Pins|14| | ||
| - | ^Pin spacing|0.1| | + | ^Pin spacing|0.1"| |
| - | ^ ^^^Arduino test rig ((reminder for my personal testing, not useful for anyone else!))|| | + | ^ |
| - | ^Pin#^IC pin^Label^Pin^colour| | + | ^Pin#^IC pin^Label^Pin| |
| - | ^1|23 |gnd|gnd | + | ^1|23 |gnd|gnd | |
| - | ^2|33|vcc|+5v|red| | + | ^2|33|vcc|+5v| |
| - | ^3|30|v5| | + | ^3|30|v5|Contrast adjustment ((connect to potentiometer between Vcc and GND))| |
| - | ^4|36|rs|d8|yellow| | + | ^4|36|rs|d8| |
| - | ^5|37|r/ | + | ^5|37|r/ |
| - | ^6|38|e|d9|blue| | + | ^6|38|e|d9| |
| ^7|39|d0| | ^7|39|d0| | ||
| ^8|40|d1| | ^8|40|d1| | ||
| ^9|41|d2| | ^9|41|d2| | ||
| ^10|42|d3| | ^10|42|d3| | ||
| - | ^11|43|d4|d4|purple| | + | ^11|43|d4|d4| |
| - | ^12|44|d5|d5|grey| | + | ^12|44|d5|d5| |
| - | ^13|45|d6|d6|white| | + | ^13|45|d6|d6| |
| - | ^14|46|d7|d7|black| | + | ^14|46|d7|d7| |
| - | \\ | + | |
| - | \\ | + | |
| - | 16 x 1 characters, but logically laid out as two lines of 8 characters. | + | |
| - | + | ||
| - | The contrast adjustment v5 needs to be connected to a 10kΩ potentiometer between +5v and ground. | + | |
| The LCD is mounted on a sub-board that can be unsoldered from the mainboard. | The LCD is mounted on a sub-board that can be unsoldered from the mainboard. | ||
| ---- | ---- | ||
| - | ===== Examples from Canon LBP-8 III printer : ===== | + | ===== Datasheets |
| + | * {{: | ||
| + | * {{: | ||
| - | {{: | + | \\ |
| + | ---- | ||
| + | ===== Examples ===== | ||
| + | ^Recovered from Canon LBP-8 III printer :^ | ||
| - | {{: | + | {{: |
| - | {{: | + | {{: |
| - | {{: | + | {{: |
| + | |||
| + | {{: | ||
| + | |||
| + | {{: | ||
| + | |||
| + | {{: | ||
| + | |||
| + | {{: | ||
| + | |||
| + | {{: | ||
| + | |||
| + | \\ | ||
| + | ^Recovered from HP LaserJet III printer :^ | ||
| - | {{: | + | {{: |
| - | {{: | + | {{: |
| - | {{: | + | {{: |
electronic/lcd/lbp8iii.1523227075.txt.gz · Last modified: 2018/04/08 22:37 by tony
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International